A Beginner's Guide to the Steel Construction Manual, 13^th ed. (old)

Chapter 8 - Bending Members

© 2006, 2007, 2008 T. Bartlett Quimby

Section 8.6.1

Selecting Sections

Last Revised: 06/16/2011

The objective of the selection process is, generally, to select the least cost (this is also frequently the lightest) member that satisfies the design criteria.  For beams, there are multiple limit states to consider.  Generally, only one limit state will control a particular selection.

The selection criteria can be stated as:

Select the lightest section such that:

• Req'd M_n < Actual M_n,
• Req'd V_n < Actual V_n, and
• Actual D < Allowed D (There can be several of these limits).

Experience with the selection process shows that

• short span beams with heavy loads tend to be controlled by the shear limit state,
• medium span beams tend to be controlled by the flexural limit state, and
• long span tend to be controlled by the deflection limit state.

This is useful to know when making your initial selection.  If you suspect that a particular limit state is likely to control, you can solve the limit state for the associated section property, then search the section tables for the most likely section to try.  Before you are through, however, you must show that ALL limit states are satisfied.

There are several different methods that can be used in the search for the optimum method.  The method you use is not important as long as you find the right member.  The chosen method will depend on the computational tools that you have available to you and what your feel comfortable with.

Using Sorted Section Property Tables

When plastic behavior controls the shear and flexure limit states, you can solve the limit state inequalities for the required related section properties, shear area and plastic section modulus.  For deflection limit states you can always solve for required moments of inertia.

When plastic behavior controls for shear and flexure, or when selecting members based on deflection, the process can be enhanced by using sorted section property tables.  The section property tables can be sorted by shear area (A_w), plastic section modulus (Z_x and Z_y), and moment of inertia (I_x and I_y) so that you can quickly find the most likely sections for your application.  This is easily done with the section database provided with the SCM.  Additionally the SCM has tables where the sections have been sorted by selected section properties.  See SCM Tables 3-2, 3-3, 3-4, and 3-5 starting on SCM page 3-11.   In addition to section properties, some of the tables include additional section related data.  For example, the Z tables include compact criteria and moment capacities that are based on an F_y of 50 ksi.  Only the first two columns can be used when using a material with an F_y other than 50 ksi.

When sorting the tables for these section properties, be aware that resulting table is NOT sorted by LEAST WEIGHT!  This means that the section with properties closest to the value you are searching for may not be the lightest section to meet the criteria.  For example, look at SCM Table on SCM page 3-11.  If you are looking for the lightest section that has a Z_x that is greater than or equal to 1500 in³, the best choice is not the one (W36x361) that has the closest Z_x that meets the criteria.  Notice that the W44x335 also meets the criteria for Z_x but is lighter than the W36x361, making it a better choice.  It also has reserve capacity, which is a bonus.

The table identifies the lightest choice with bold font and a space between it and the next range.  Note that the bolded section is always lighter than the one on either side of it in the table.  Using this observation, you can create your own tables in a spreadsheet by using the database on the CD provided by AISC.  To do this, sort the section tables by the section property of interest then use an "if" statement in an adjacent column to identify if the current section is lighter than both the one before and the one after.

Once a section is chosen, then all the limit states are computed to show that it satisfies all the applicable limit states.  If it does not, a new member is selected based on the controlling limit state.

The "Hunt & Peck" Method

The Hunt & Peck method can always be used, regardless of the controlling flexural or shear limit state.  This method involves searching through the section table using some means (i.e. algorithm) for determining the next section to try.

Once a selection is chosen, then all the limit states are computed to show that it satisfies all the applicable limit states.  If it does not, a new member is selected based on the controlling limit state.

One way of implementing this method, is to search through a given size category (say the W18s) for the lightest section that works, then move to the other size categories.  As each size category is investigated, only sections with weights less than the current best choice are considered.

The "Brute Force" Method

This method always works regardless of the controlling limit state and is best done with a spreadsheet or computer program.

In this method, a table is made that has all the sections you wish to consider (such as all the I shapes, all the rectangular HSS shapes, etc) and their section properties needed to compute the limit states.  Additional columns are then added to compute the various limit states.  Once all the limit states have been computed, the sections with violated limit states are deleted and the remaining table sorted by weight.

Conceivably, you can create a big table for beam design for all the sections of a particular type then just copy this over and do the eliminations and sorts for a given problem.

This method is computationally intensive but very easily done in a spreadsheet.  It will always get the best result, after all the programming is debugged!

<<< Previous Section <<<        >>> Next Section >>>